|
 |
 |
| Pharm-A-Line V & VI |
 |
| Medical Grade Clear
and Flexible Tubing For Chemical Service |
|
Pharm-A-Line
V and VI offer the benefit of a co-extrusion
which incorporates the best properties of two dissimilar
materials.
The liner or
contact surface is comprised of chemically
inert clear low density polyethylene material. The
outer shell is constructed of Ethylene vinyl acetate
(EVA) which provides the flexibility
and clarity the
tubing offers. Both materials are pharmaceutical
grade and have superior purity properties. Pharm-A-Line
V and VI will not be attacked by most solvents,
including acetone and unlike PVC, Silicone™ or
C-Flex™ there are no oils
or plasticizers that
can leach from the tubing.
The benefit
of Pharm-A-Line V or VI is a seamless, light
weight, clear and flexible tubing. Pharm-A-Line V and VI
meet the most stringent criteria for medical device
and biopharmaceutical transfer. The co-extruded tubing offers superior burst strength
over single walled, conventional thermoplastics such
as PVC.
While both Pharm-A-Line V and
VI are made of the same base materials, Pharm-A-Line
V is gamma treated which cross-links the material
for even higher thermal, chemical, and mechanical
performance.
|
 |
Sizing
Chart |
|
| P/N |
ID |
OD |
Wall |
|
S/L |
Tri
Clamp |
| TBL-05*1 |
1/16" |
3/16" |
1/16" |
1 |
50',
100' |
Mini |
| TBL-05*2 |
1/8" |
3/16" |
1/32" |
4 |
50',
100' |
Mini |
| TBL-05*3 |
1/8" |
1/4" |
1/16" |
5 |
50',
100' |
Mini |
| TBL-05*4 |
3/16" |
1/4" |
1/32" |
8 |
50',
100' |
Mini |
| TBL-05*6 |
1/4" |
3/8" |
1/16" |
13 |
50' |
Mini, 1" |
| TBL-05*7 |
5/16" |
7/16" |
1/16" |
16 |
50' |
Mini, 1" |
| TBL-05*8 |
3/8" |
1/2" |
1/16" |
19 |
50' |
Mini, 1" |
| TBL-05*9 |
3/8" |
5/8" |
1/16" |
21 |
50' |
Mini, 1" |
| TBL-05*10 |
1/2" |
5/8" |
1/16" |
25 |
50' |
Mini, 1" |
| TBL-05*11 |
1/2" |
3/4" |
1/8" |
27 |
50' |
Mini, 1" |
| TBL-05*12 |
3/4" |
1" |
1/8" |
38 |
50' |
Mini, 1" |
| *
Replace with V for Pharm-A-Line V *
Replace with Vl for Pharm-A-Line Vl |
|
Additional
Data |
|
| Values |
|
| Durometer,
Shore A (5SEC.ASTM D2240) |
64 |
| Tensile
Strength, psi (ASME D-412) |
1,050 |
| Elongation,
% (ASTM D-412) |
375 |
| Tensile
Stress @ 100 psi (ASTM D-412) |
400 |
| Tension
Set, % |
47 |
| Tear
Resistance Lb/in |
128 |
| Compression
Set Constant Deflection “B” (22hrs.
@ 70° C), % |
32 |
| Abrasion
Resistance, Mg. lost/1,000 cycles |
1.2 |
| Brittle
Point, °F (ASTM D-789) |
-76F |
| Low
Temp. Flex at -40 |
Passed |
| Flame
Resistance Vertical Plane (Average Burning Rate-cm/min |
22 |
| Heat
Resistance |
275 |
| FDA
Reg. No. |
21CFR177.2600 |
|
|
|
Operating
Conditions |
|
|
- Pharm-A-Line V -60° to 200° F (-51° to
93° C)
- Pharm-A-Line
VI -60° to 160° F (-51° to
71° C)
|
|
|
Benefits |
|
|
- Superior Chemical Resistance
- Flexible
- Clear
- Welds with RF and conventional heat sealers
- Easy to post fabricate
- Superior pressure rating
- Non Hemolytic
- Low cost
|
|
|
Packaging |
|
|
- Continuous coils
- Pre cut lengths
- Clean Room Packaged
|
|
|
Sterilization |
|
|
- Ethylene oxide (ETO)
- Gamma irradiated
|
|
|
Certifications |
|
|
- U.S. Pharmacopoeia
Class VI Certification
- Cytotoxicity Criteria
- CFR Title 21 Section 177.1350
- CFR Title 21 Section 177.1520
- Traceability: Lot and Batch
- Certification: Lot and Batch
- Current Good Manufacturing Practices (CGMP)
- Animal Derived Ingredient Free
|
 |
|
|
 |
|
